Vendor Name: Cisco
Exam code: 200-001
Exam Name: Implementing Cisco Video Network Devices
Click the link below to get full version
http://www.certifyguide.com/exam/200-001/
|
Question: 1
|
Cisco Video Surveillance Video
Encoder Cards perform which function?
A. The ability to use existing
equipment with an IP-Enabled video Surveillance system
B. The ability to encrypt raw
video signals to secure video signals
C. The ability to convert low
resolution video to high-definition video for video surveillance
D. The ability to stream
digital media to digital media in an IP-enabled video recording environ
|
Answer: A
|
|
Question: 2
|
Refer to the exhibit.
Which tab can be used in order
to check the call statistics for the Cisco TelePresence Codec C60?
A. Configuration
B. Maintenance
C. Diagnostics
D. Call control
E. The GUI cannot be used to
view call statistics
|
Answer: C
|
|
Question: 3
|
Threat monitoring in physical
access security can be based upon which three of these? (Choose three)
A. Weather
B. Fingerprints
C. Badges
D. Age
E. Doors
F. Height
|
Answer: B, C, F
|
|
Question: 4
|
During the initial setup of
Cisco TelePresence System 500, you are required to do an initial camera setup.
What might be a primary reason that the failure occurs?
A. The room is too dark
B. The system is too far away
from the target
C. The camera cannot focus on
the target
D. The cable to the camera is
not connected correctly
|
Answer: A
|
|
Question: 5
|
Which two of these support an
ad-hoc conference call? (Choose two)
A. Using the booking tab in
the Cisco TelePresence Maintenance State to configure a new conference
B. Using the Cisco
TelePresence Management Suite Scheduler to schedule a conference call to start
in 5 minutes.
C. Using the tab Administrative
Tools > Configuration > Conference Settings on the Cisco TelePresence
Management Suite.
D. Pressing the conference
button on Cisco Unified IP Phone 8941 conference in a third call.
E. Cisco TelePresence Multi
way with Cisco TelePresence Multipoint Control Unit and Cisco TelePresence
Video Communication Server.
|
Answer: C, D
|
|
Question: 6
|
Which three of these are valid
ways to initially configure a C-Series codec in a network where DHCP is not
used? (Choose three)
A. Secure web browser
B. Telnet
C. Tandberg Remote Control V
D. Touch screen interface
E. CLI using a console cable
F. Secure copy program
|
Answer: A, C, E
|
|
Question: 7
|
Instructions:
To access the multiple-choice
question, click on the tab titled “Questions” on the button of the panel.
Scenario:
In this item, you will need to
use all informartion presented to you to successfully answer the question.
Refer to the exhibits. An administrator needs to perform a factory reset on a
C-Series endpoint. What are two valid ways to accomplish this task? (Choose
two)
A.
B.
C.
D.
|
Answer: A, C
|
|
Question: 8
|
When configuring the Cisco
TelePresence System 500 with IP address, where should the IP address be
configured?
A. In Cisco Unified
Communication Manager after adding the Cisco TelePresence System 500 manually.
B. In the Cisco TelePresence
Administration tool.
C. Static IP address
configuration is not possible. Only a DHCP-provided IP address is supported.
D. Using the on-screen display
E. In the Cisco TelePresence
System 500 was added under systems.
|
Answer: E
|
|
Question: 9
|
Which CLI command can be used
to reset the Cisco TelePresence System 500-32 personal video system to a
factory condition?
A. Utils system factory init
B. xcommand SystemUnitReset
C. xconfiguration default
factory
D. utils reset factory
E. utils factory reset 2
F. xcommand defaultvalues set
level: 2
|
Answer: A
|
|
Question: 10
|
When connecting to a
pan-tilt-zoom camera to a C-Series codec, what type of cable must be used for
camera control?
A. An Ethernet crossover cable
(RJ-45-to-RJ45)
B. A serial cable
(DB25-to-DB9)
C. A VISCA cable (DB-to-RJ45)
D. An Ethernet cable
(RJ45-to-RJ45)
|
Answer: C
|
|
Question: 11
|
You have installed a C-Series
in an officer where DHCP in not supported. At a minimum, which four network
items must be configured for the endpoint to be able to register with H.323 on
a Cisco TelePresence Video Communication Server located at the external
headquarters locations? (Choose four)
A. Default gateway
B. Cisco VCS IPv4 address
C. SMTP server IPv4 address
D. Subnet mask
E. Active Directory IP4address
F. Unique IPv4 address
|
Answer: A, B, D, F
|
|
Question: 12
|
What is the importance of
defining option 150 in the DHCP server for Cisco TelePresence endpoints?
A. It is the IPv4 address of
the default gateway for the subnet that the video endpoints is connected to.
B. It is the configured SIP
register and proxy server.
C. It is the unique NTP server
IPv4 address.
D. It is the unique NTP server
IPv4 address.
E. It is the TFTP server IPv4
address where the video endpoint retrieves its configuration file while
booting.
F. Option 150 is not
importance.
|
Answer: E
|
|
Question: 13
|
You have been informed from
the field that a new Cisco TelePresence video endpoint has been deployed with
an IPv4 address of 172.28.254.45. You need to check for connectivity from the
Cisco Unified Communications Manager server. Which command should be entered to
check for network connectivity?
A. Utils network traceroute
newsystem.domain254.local
B. Utils network host
cucum.osl147.local
C. Traceroute 172.28.255.255
D. Ping 172.28.254.45
E. Utils network ping
172.28.254.45
|
Answer: E
|
|
Question: 14
|
Which two of these are
considered to be provisioning and scheduling management tools in a Cisco
TelePresence environment? (Choose two)
A. Cisco TelePresence
Management Suite
B. Cisco TelePresence Manager
C. Cisco TelePresence
Multipoint Control Unit
D. Cisco Video Surveillance
management Server
E. Cisco Video Surveillance
Operations Manager
|
Answer: A, B
|
|
Question: 15
|
What is the main difference
between Cisco Jabber and Video TelePresence?
A. Cisco Jabber has no video
calling capabilities, whereas Cisco Jabber Video for TelePresence has video
capabilities.
B. There is no difference
between Cisco Jabber and Cisco Jabber Video for TelePresence. They should not
coexist in the same network
C. Cisco Jabber has no
presence capabilities, whereas Cisco Jabber Video for TelePresence
capabilities.
D. Cisco Jabber registers to
the Cisco Unified Communication Manager, whereas Cisco Jabber Video for
TelePresence registers to the VCS.
E. Cisco Jabber Video for
TelePresence Registers to Cisco Unified Communication Manager, Whereas Cisco
Jabber Registers to the VCS.
|
Answer: B
|
No comments:
Post a Comment